ASTM A36 steel plate is the most purchased hot rolled steel plate in the world and the least expensive of the commercial carbon steels. The heat ability reates very good welding properties, and the 36 ksi yield strength makes ASTM A36 steel plate acceptable for most applications. A36 is considered a mild steel due to its relatively moderate hardness.
Coyote Steel & Co. 2030 Cross Street Eugene, Oregon 97402 USA No. 1 Handbook of STEEL SIZES & WEIGHTS For Industry Phone:541-461-2060 Toll-free:1-800-553-0240 Hot Rolled Steel AK Steellimits, please contact your AK Steel sales representative. The standard inner diameter of hot rolled pickled coils is 24 in. (610 mm) while hot bands have inside diameters of 30 in. (762 mm) for Middletown Works and 26 28 in. (660 711 mm) for Dearborn Works. Thickness, width, and flatness tolerances are covered in ASTM A568 or A635.
Generally, hot rolled plate surface smoothness cannot meet the requirements, so hot rolled steel strip needs cold rolling, and the minimum thickness of hot-rolled steel is general at 1.0 mm, while cold rolling can reach 0.1mm. IS 1730 (1989):Dimensions for steel plates,sheets strips 4.1 Thickness 8 TOLERANCES The standard nominal thickness of plates shall be as given in Table 1. 8.1 The rolling and cutting tolerances and mass tolerances for steel plates, sheets, strips and. flats shall be as laid down in IS 1852 :1985. 1
Table 26 Plates:Sizes of Mild Steel Plates Chequered Plates Metric units 8.08kg/mm m 2 - 0.7507 kg/mm ft 2 Width x Length (ft) 4x 8 4 x 10 4 x 16 4 x 20 5 x 10 5 x 20 Thickness Weight Weight / pc mm kg/ft2 kg kg kg kg kg Kg 2.3 1.73 55.2 69.1 111 86.3 - 3 2.25 Mild Steel PlatesTable 26 Plates:Sizes of Mild Steel Plates Chequered Plates Metric units 8.08kg/mm m 2 - 0.7507 kg/mm ft 2 Width x Length (ft) 4x 8 4 x 10 4 x 16 4 x 20 5 x 10 5 x 20 Thickness Weight Weight / pc mm kg/ft2 kg kg kg kg kg Kg 2.3 1.73 55.2 69.1 111 86.3 - 3 2.25
Because of the forces required during rolling, the work rolls can deflect resulting in a crown on the plate where the thickness at the middle is greater than at the edges. The thickness tolerances established for these discrete (Quarto) plates were defined in ASTM A 480, Table A2.17. Plate Rolling Machine Operation Procedure and Method The parameters of the steel plate:the yield limit of the steel plate, the minimum allowed rolling diameter, the width of the steel plate and the thickness of the steel plate shall be allowed within the parameters of the rolling machine. Steel plate surface quality:the cutting edge of the plate shall not have obvious defects, and the surface
Rolling of Metals Rolling reducing the thickness or changing the cross-section of a long workpiece by compressive forces applied through a set of rolls Developed in late 1500s Accounts for 90% of all metals produced by metal working processes Often carried out at elevated temperatures first (hot STEEL PLATES - steel-nPlate Mill 1 Plate Mill 2 Plate Mill 3 Plate Mill 4 Operation jul. 1972 Feb. 1978 Nov. 1997 Aug. 2010 Capa(ton/y) 620,000 2,700,000 1,180,000 2,500,000
Low Carbon Steel Plates that have a blend of strength, durability, and weldability are those steel plates from the Philippines that has a thickness of over 1 ½ and carbon components 0.20 increasing until 0.33. ASTM A36 PLATE STEEL- This is a specific kind of low carbon steel plate that elicits great strength and is easy to fabricate and welded. Steel Plate Philippines - Regan IndustrialThe steel plate that falls under this category has the lowest carbon range of 0.10 up to 0.20 and are significantly lighter with a thickness of ¾. Steel plates with these compositions have the highest cold forming property and welding capability.
We offer steel plate and steel sheet in a broad range of lengths, widths, gauges, alloys, and specifications to meet your material requirements. Read more info about advantages and applications for steel sheet & plate. We stock steel sheet and plate in 36, 48, and 60 widths and in Steel Standards - ASTM InternationalStandard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Alloy, Drawing Steel and Structural Steel, Hot-Rolled A1039 / A1039M - 20 Standard Specification for Steel, Sheet, Hot Rolled, Carbon, Commercial, Structural, and High-Strength Low-Alloy, and Ultra-High Strength, Produced by Twin-Roll Casting Process
Steel, Metal and Alloy Plate Rolling, Forming, Fabricating, Processing, Welding and Bending Services. Call 1-800-423-7080 for a Quote. To Submit an RFQ, CAD Drawing or P.O. Email [email protected] The Halvorsen Company provides plate rolling services, working with carbon steel, carbon alloys, stainless steel, stainless alloys, aluminum Steel Plates - Size & Weight - Engineering ToolBoxSteel Plate Thickness and Weight - Imperial Units 1 in = 25.4 mm 1 lb/ft2= 4.88 kg/m2 Steel sheets and plates are typical stocked in 36, 48, and 60 widths and 96, 120, and 144 lengths.